 |
We
have been working hard on supplying the new Virtual Drumline
template for Sibelius 5 users. Sibelius has made some major changes
in how it now deals with playback of virtual instruments like
VDL. This new system (called "SoundWorld") is pretty
slick, so we hope you'll find it was worth the wait. Special
thanks go out to Hugh Smith for spearheading the template project.
Below
are steps to take in configuring Sibelius 5.1 to make best use
of the new template and sound set. Also included are some informal
tutorial videos created by Jim Casella to help walk you through
the process on-screen, as well as a few videos using VDL with some
new features in Sibelius 5 worth noting.
|
NOTE: These
steps are merely a basic overview. For more information, refer
to the README file that comes with the VDL/Sibelius
5.1 Template.
Also,these
tutorials are directed toward users of the full Virtual Drumline
product. If you are using Sibelius "Essentials" (the
free library that comes with Sibelius 5 and contains a few
basic VDL patches) the Tapspace VDL sound set and template
for Sibelius are not supported. |
NOTE: If you are using a more current version of Sibelius 5, please click
these links for information specific to those versions:
TUTORIAL SCREENCASTS FOR THE SIBELIUS 5.1 TEMPLATE
Step
1 -Upgrade to Sibelius 5.1
Obviously, you'll already need to be a registered user of Sibelius 5 to do
this. It's important to use Sibelius 5.1 due to several modifications that
were made in the software which will help it interface smoothly with VDL.
Watch the Screencast
(2.1MB - 1 minute).
Step
2 - Download the VDL/Sibelius 5.1 template and install the customized Tapspace
VDL 2.5 Sound Set
When you installed Sibelius 5.1, you'll see there's already a sound set
present called "Virtual Drumline 2.5." There are, however, a
few important modifications we've had to make to ensure smooth operation
with the VDL/Sibelius template, so for best results, you must install the
updated Tapspace sound set as well. This file is named Tapspace Virtual Drum Line 2.5.xml,
and is included with the VDL/Sibelius 5.1
Template. Once you've installed this, it'll appear in Sibelius as "Tapspace
Virtual Drumline 2.5." This naming is important to note to ensure you're
selecting the correct one within Sibelius.
Watch the screencast
(8.8MB - 2 minutes).
Step
3 - Set up your Playback Configuration
With Sibelius 5's new ability to host VST or AU plugins, the Playback Devices
window has been significantly redesigned. To ensure proper playback with KontaktPlayer2
and your sounds from VDL 2.5, your playback configuration should be properly
setup. The concept of playback configurations is worth getting to know well
to ensure you're working properly.
In
Sibelius, each active instance of KontaktPlayer2 will allow 16 instruments
to be loaded into it. Sibelius will load instruments from the library corresponding
to the sound set you've assigned it. So if you only need a few percussion
instruments, one activated KP2 (with Tapspace VDL 2.5 sound set assigned)
will be sufficient. If you'll need more than 16 VDL instruments, activate
a second instance of KP2 (and again, assign the Tapspace VDL 2.5 sound set).
More than 32 instruments - activate a third instance, and so on. If you need
brass or woodwind sounds within the same score, activate a separate instance
of KP2 and assign the Essentials sound set to it.
Watch the Screencast
(10.7MB - 7:08).
Step
3a - Configure Preferences (optional)
Sibelius
has some preferences that may be helpful in streamlining
your process. Watch
the screencast (9.3MB - 5:50) for a few suggestions.
Step
4 - Open the Template, create instruments and start writing!
Once you open the template, it's simply a matter of creating your
instruments (Create>Instruments) and assigning them to the VDL instruments
that have been pre-configured in the template. Now with Sibelius 5, adding
instruments to your score not only creates their staves, but loads your patches
for you as well! Watch this screencast
(16.3MB - 8:30) to see how quick and easy this is.
A
FEW EXTRA POINTS OF INTEREST
The
Playback Dictionary
For a quick demonstration of how certain features of VDL instruments are now
controlled via the playback dictionary within Sibelius (such as MW
changes and Keyswitches), watch
this screencast (15.5MB - 7:42). For a full listing of Dictionary text,
please refer to the README file included with the template.
Instrument
Changes
Also new to Sibelius 5 are Instrument Changes. If you are familiar
with the old Staff Type Changes from Sibelius 4, Instrument Changes now do
the same thing, but also contain playback information so that Sibelius will
automatically load your selected patch without you ever having to open KontaktPlayer. Watch
this screencast (12.4MB - 5:35) for a demonstration.
Noteheads
Using correct notehead numbers will ensure Sibelius plays your sounds correctly.
Entering notes via MIDI keyboard will generally assign noteheads correctly
without needing to edit them. However, there are a few cases where changing
noteheads may be necessary to achieve your desired sounds. These techniques
can also be useful for people wishing to work without a MIDI keyboard at
all. Watch this screencast (28MB - 10:45) for
a demonstration.
The
video files on this page require that you are using the current version of QuickTime on
your computer.
| 
